Hubbell Network Cables 69320 101 User Manual

Pub. 42004-693L2C  
G AI - TRO NI CS® CO RPO RATI O N  
A
H U B B E L L C O M P A N Y  
Model 69320-101  
Voice Network Adapter  
Confidentiality Notice  
This manual is provided solely as an operational, installation, and maintenance guide and contains sensitive  
business and technical information that is confidential and proprietary to GAI-Tronics. GAI-Tronics retains  
all intellectual property and other rights in or to the information contained herein, and such information may  
only be used in connection with the operation of your GAI-Tronics product or system. This manual may  
not be disclosed in any form, in whole or in part, directly or indirectly, to any third party.  
General Information  
The Model 69320-101 Voice Network Adapter (VNA) allows voice communication between  
interconnected SmartSeries systems. It is installed in a 10457 Series Card Rack (Card Rack) and is  
controlled by a 69254 Series or 69440 Series Master Control Unit (MCU) installed in that same card rack.  
The VNA is designed exclusively for use in a SmartSeries system, and is not intended for use with other  
types of equipment.  
Description of Major Components  
Front Panel LEDs  
The following table describes the LEDs mounted on the VNA’s front panel:  
LED  
Status  
Description  
On  
The MCU is running and is configured to recognize the VNA.  
ON LINE  
(green)  
Off  
On  
The VNA is not receiving power from the card rack or the MCU is not  
properly configured to recognize the VNA.  
VNA FLT  
(red)  
The MCU has lost communication with the VNA. The MCU and the VNA  
continuously update handshaking information. If the VNA is not updating that  
information as the MCU expects, then the MCU turns on this LED.  
Off  
The “On” condition is not occurring.  
GAI-Tronics Corporation P.O. Box 1060, Reading, PA 19607-1060 USA  
610-777-1374 800-492-1212 Fax: 610-796-5954  
VISIT WWW.GAI-TRONICS.COM FOR PRODUCT LITERATURE AND MANUALS  
 
Pub. 42004-693L2C  
Page: 3 of 15  
Model 69320-101 Voice Network Adapter  
LED  
Status  
Description  
On  
LOS/RCL  
(red)  
The VNA is not receiving a T1 signal (Loss of Signal or Receive Carrier  
Loss), and does not detect an open on its T1 transmit line.  
Flashing The VNA both is not receiving a T1 signal and detects an open on its T1  
90% On transmit line. The frequency of flashing is approximately one Hertz.  
Flashing The VNA detects an open on its T1 transmit line, and is receiving a T1 signal.  
50% On The frequency of flashing is approximately one Hertz.  
Flashing The T1 transceiver on the VNA is not initialized. The frequency of flashing is  
10% On  
approximately one Hertz.  
Off  
All of the above four conditions are not occurring.  
Connections to the Field Wiring Terminal Blocks  
69320-101 Voice Network Adapter Connections to the Field Wiring  
Connections to the field are made via the upper DB25 connector on the rear of the 10457 Series Card Rack  
assembly. This connector can be utilized by a direct connection of a DB25 cable to the field equipment, a  
DB25 cable to a DIN rail-mounted terminal block adapter, or with the use of a DB25-to-RJ45 connector  
adapter. The pinout definition for the DB25 connection is shown is the table below.  
Upper DB25 Connector  
Pin  
Signal  
Tx (ring)  
1
2
5
6
Tx (tip)  
Rx (ring)  
Rx (tip)  
Included with the VNA are two DB25-to-RJ45 connector adapters. The 21246-014 Connector Adapter  
brings the transmit pair to the RJ45 pins 1 and 2 and the receive pair to pins 4 and 5. The 21246-008  
Connector Adapter brings the transmit pair to the RJ45 pins 4 and 5 and the receive pair to pins 1 and 2.  
These adapters permit the use of non-crossover Ethernet cables for the connections to field equipment  
utilizing these same pins on an RJ45 connector.  
Cabling to the field equipment should be a twisted pair design.  
\\s_eng\gtcproddocs\standard ioms - current release\42004 instr. manuals\42004-693l2c.doc  
04/06  
 
Pub. 42004-693L2C  
Page: 4 of 15  
Model 69320-101 Voice Network Adapter  
Switch and Jumper Settings  
Overview  
Several switch and jumper settings are required for proper operation of the VNA Card. The following  
settings are set during the system commissioning and programming and should not be changed. If replacing  
an existing 69266-001 T1 card or VNA card for maintenance purposes, be sure to replicate the switch and  
jumper setting of the card being replaced. Refer to Figure 1 for the switch and jumper locations.  
Front Panel DIP Switch (SW5) Settings  
NOTE: The front panel DIP switches (SW5) can be updated without powering down the card rack and  
without resetting the MCU.  
Position  
Number  
Name  
Top  
1
2
3
4
5
6
7
8
Line Build 0 (LB0)  
Line Build 1 (LB1)  
Line Build 2 (LB2)  
Receive Equalizer Gain Limit  
Lamp Test  
Customer Disconnect Enable  
Local Loop Back  
Bottom  
Remote Loop Back  
The Line Build # switches control the “line build” (signal’s amplitude) of the T1 transmit line. Set the Line  
Build # switches according to the following table:  
LB0  
LB1  
LB2  
T1 Line Length  
Open  
Open  
Open  
Open  
Open  
Open  
Open  
DSX-1 (0 to 133 feet) / 0 dB CSU  
Closed DSX-1 (133 to 266 feet)  
DSX-1 (266 to 399 feet)  
Closed DSX-1 (399 to 533 feet)  
Open DSX-1 (533 to 655+ feet)  
Closed -7.5 dB CSU  
Open -15 dB CSU  
Closed Open  
Closed  
Closed Open  
Closed Open  
Closed Closed  
Closed Closed Closed -22.5 dB CSU  
\\s_eng\gtcproddocs\standard ioms - current release\42004 instr. manuals\42004-693l2c.doc  
04/06  
 
Pub. 42004-693L2C  
Page: 5 of 15  
Model 69320-101 Voice Network Adapter  
The Receive Equalizer Gain Limit switch controls the similarly named feature of the T1 transceiver. Set  
the Receive Equalizer Gain Limit switch according to the following table:  
-36 dB (long haul)  
Open  
-15 dB (limited long haul)  
Closed  
The Lamp Test switch turns on all LEDs on the VNA’s front panel. It is used during production of the  
VNA. The Lamp Test switch will not function when the VNA detects the MCU (MCU FLT LED is Off).  
Set the Lamp Test switch according to the following table:  
All front panel LEDs function normally.  
All front panel LEDs are ON  
Open  
Close  
The Customer Disconnect function presents a well-behaved signal on the T1 line. This signal is sometimes  
useful during troubleshooting and verification. Set the Customer Disconnect Enable switch according to the  
following table:  
The T1 transceiver is operating normally.  
Open  
The Customer Disconnect signal is being transmitted on the T1 line. This setting disrupts the  
T1 signal and the MCU reports a T1 line fault.  
Closed  
The Local Loop Back feature sometimes is used during troubleshooting. Set the Local Loop Back switch  
according to the following table:  
The T1 transceiver is operating normally.  
Open  
The “Framer Loopback” feature of the T1 transceiver is enabled. The T1 transceiver transmits  
the Blue Alarm on the T1 transmit line during this condition. This setting disrupts the T1 signal  
and the MCU reports a T1 line fault. This setting causes the VNA to receive the T1 signal it  
normally would transmit, while actually transmitting the Blue Alarm.  
Closed  
The Remote Loop Back feature sometimes is used during troubleshooting. Set the Remote Loop Back  
switch according to the following table:  
The T1 transceiver is operating normally.  
Open  
The “Remote Loopback” feature of the T1 transceiver is enabled. This setting disrupts the T1  
signal and the MCU reports a T1 line fault. This setting causes the VNA to transmit its received  
T1 signal. The T1 standards mention two types of loopbacks: “line” and “payload”; this  
loopback is a “line” loopback.  
Closed  
\\s_eng\gtcproddocs\standard ioms - current release\42004 instr. manuals\42004-693l2c.doc  
04/06  
 
Pub. 42004-693L2C  
Page: 6 of 15  
Model 69320-101 Voice Network Adapter  
First Internal DIPSwitch (SW4)Settings  
NOTE: First internal DIP switch (SW4) changes only take effect after powering down the card rack;  
resetting the MCU is insufficient.  
Position Number  
Name  
Left  
1
2
3
4
5
6
7
8
ST-Bus Clock Master  
T1 Clock Master  
T1 Synchronous  
E1 Select  
Sampling Rate Select  
Reserved  
Reserved  
Right  
Reserved  
Set the ST-Bus Clock Master switch according to the following table:  
The VNA generates the Card Rack’s backplane ST-Bus clock signals. The VNA is the ST-  
Bus Clock Master.  
Open  
The VNA receives the Card Rack’s backplane ST-Bus clock signals. The VNA is a ST-Bus  
Clock Slave.  
Closed  
Set the T1 Clock Master switch according to the following table:  
The VNA uses its received T1 signal’s timing to generate its transmitted T1 signal’s timing.  
The VNA is a T1 Clock Slave.  
Open  
The VNA uses the Card Rack’s backplane ST-Bus clock signals to generate its transmitted T1  
signal’s timing. The VNA is the T1 Clock Master.  
Closed  
\\s_eng\gtcproddocs\standard ioms - current release\42004 instr. manuals\42004-693l2c.doc  
04/06  
 
Pub. 42004-693L2C  
Page: 7 of 15  
Model 69320-101 Voice Network Adapter  
Set the T1 Synchronous switch according to the following table:  
The VNA is frequency locked to the received T1 signal. This setting is ignored if the VNA is  
both a ST-Bus Clock Slave and a T1 Clock Slave.  
Open  
The VNA is not frequency locked to the received T1 signal. “Elastic store” buffers in the T1  
transceiver integrated circuit either duplicate or drop a frame as needed.  
Closed  
Set the E1 Select switch according to the following table:  
The VNA uses T1 signaling.  
Open  
The VNA uses E1 signaling. NOTE: Upon initial release of the VNA, this feature does not  
function properly.  
Closed  
The Sample Rate Select switch configures the VNA’s codec’s sampling rate. The VNA’s codec can run at  
either 8,000 samples per second (8 kHz), or 16,000 samples per second (16 kHz). The VNA accepts and  
generates 69266-001 T1 Interface wide bandwidth page audio regardless of the setting of this switch. Set  
the Sampling Rate Select switch according to the following table:  
The VNA’s codec uses 8 kHz sampling. Always use this setting if wide bandwidth paging is  
disabled. This setting is recommended.  
Open  
The VNA’s codec uses 16 kHz sampling.  
Closed  
Set the Reserved switches according to the following table:  
Use this setting to help insure future compatibility.  
Open  
Do not use this setting. Using this setting may increase the risk of unexpected behavior when  
upgrading the VNA.  
Closed  
\\s_eng\gtcproddocs\standard ioms - current release\42004 instr. manuals\42004-693l2c.doc  
04/06  
 
Pub. 42004-693L2C  
Page: 8 of 15  
Model 69320-101 Voice Network Adapter  
Second Internal DIP Switch (SW1) Settings  
SW1 is unused. Leave all switches open to aid in future compatibility.  
Rotary Switch and Jumper Settings  
The 2xx/3xx Address (P2) shorting clip selects part of the base input/output address used by the MCU when  
accessing the VNA.  
The Board Address (SW3) rotary switch selects part of the base input/output port address used by the MCU  
when accessing the VNA.  
The Board Identification (SW2) rotary switch lets the MCU distinguish between multiple VNAs installed in  
the same card rack.  
\\s_eng\gtcproddocs\standard ioms - current release\42004 instr. manuals\42004-693l2c.doc  
04/06  
 
Pub. 42004-693L2C  
Page: 9 of 15  
Model 69320-101 Voice Network Adapter  
Figure 1. Model 69320-101 Voice Network Adapter Board Layout Diagram  
\\s_eng\gtcproddocs\standard ioms - current release\42004 instr. manuals\42004-693l2c.doc  
04/06  
 
Pub. 42004-693L2C  
Page: 10 of 15  
Model 69320-101 Voice Network Adapter  
Changing to a 69320-101 VNA from a 69266-001 T1 Interface  
NOTES:  
1. The 69320-101 VNA is not electrically compatible with its predecessors. If further information on the  
differences is needed, please contact the GAI-Tronics Field Service Department at 800-492-1212.  
2. When upgrading to a 69320-101 VNA, the following four upgrades are required:  
Any 69266-001 or 69320-001 VNAs must be upgraded to the 69320-101 VNA.  
Any 69257-003, 69257-002, or 69257-001 APIs must be upgraded to the 69257-101 API.  
Any 69510-001, 69215-003, 69215-002, or 69215-001 backplane termination boards must be  
upgraded to the 69510-101 Termination board. Two of these boards are required per card rack.  
The upgraded cards must be installed in the proper backplane slot. This task involves moving the  
card and the associated ribbon cable at the rear of the card rack assembly.  
The 69266-001 T1 Interface uses a different switch and jumper collection than the VNA. The following  
text states how to convert the T1 Interface switch and jumper setting to the VNA switch and jumper  
settings.  
The 2xx/3xx Address (P2) shorting clip should be set to the 2xx position if the shorting clip on J1 of the T1  
Interface is closer to the back of the T1 Interface. Otherwise, set to the 3xx position when the shorting clip  
on J1 of the T1 Interface is closer to the front of the T1 Interface.  
NOTE: The silkscreen for J1 on the T1 interface should be blacked out; if not blacked out, then that  
silkscreen shows the 2xx / 3xx position reversed from the actual meaning of J1.  
The Board Address (SW3) rotary switch on the VNA should match the Board Address rotary switch on the  
T1 Interface.  
The Board Identification (SW2) rotary switch on the VNA should match the Board Identification rotary  
switch on the T1 Interface.  
First internal DIP switch #1 (SW4) (ST-Bus Clock Master) should be set to CLOSED if J3 of the T1  
Interface is set to ING (ignore – shorting clip towards front). Otherwise, set to OPEN when J3 of the T1  
Interface is set to GEN (generate – shorting clip towards back).  
First internal DIP switch #2 (SW4) (T1 Clock Master) should be set to CLOSED if J4 of the T1 Interface is  
set to GEN (generate – shorting clip towards front). Otherwise, set to OPEN when J4 of the T1 Interface is  
set to REC (receive – shorting clip towards back).  
First internal DIP switch #3 (SW4) (T1 Synchronous) should be set to OPEN.  
First internal DIP switch #4 (SW4) (E1 Select) should be set to OPEN.  
First internal DIP switch #5 (SW4) (Sampling Rate Select) should be set to OPEN.  
First internal DIP switch #6 (SW4) through #8 (Reserved) should be set to OPEN.  
\\s_eng\gtcproddocs\standard ioms - current release\42004 instr. manuals\42004-693l2c.doc  
04/06  
 
Pub. 42004-693L2C  
Page: 11 of 15  
Model 69320-101 Voice Network Adapter  
For front panel DIP switch #1 (SW5) (Line Build 0), front panel DIP switch #2 (Line Build 1), and front  
panel DIP switch #3 (Line Build 2) select the closest matching distance from the following two tables. If  
the S3 T1 Interface switch settings are not listed in the table, then select all OPEN for the VNA Line Build  
switches.  
S3 (XMIT EQUALIZATION) on T1 Interface  
0'  
-
75'  
150'  
225'  
300' 375' 450' 525' 600' 675' 750' 825'+  
-
-
-
-
-
X
-
-
X
-
-
X
-
X
-
X
-
X
-
X
X
X
X
X
-
X
X
X
X
-
X
X
X
X
-
S3-1  
S3-2  
S3-3  
S3-4  
S3-5  
S3-6  
S3-7  
S3-8  
-
-
-
-
X
-
X
-
X
-
-
-
-
X
X
-
X
-
X
-
-
-
-
-
X
-
X
-
-
-
-
-
X
-
X
-
X
-
X
-
-
-
-
X
-
X
-
X
-
-
X
-
-
-
-
-
-
-
-
-
X” means closed; “-” means open.  
Line Build on VNA  
Build 0  
Build 1  
Build 2  
Distance  
Open  
Open  
Open  
DSX-1 (0 to 133 feet) / 0 dB CSU  
DSX-1 (133 to 266 feet)  
DSX-1 (266 to 399 feet)  
DSX-1 (399 to 533 feet)  
DSX-1 (533 to 655+ feet)  
-7.5 dB CSU  
Open  
Open  
Closed  
Open  
Open  
Closed  
Closed  
Open  
Open  
Closed  
Open  
Closed  
Closed  
Closed  
Closed  
Open  
Closed  
Open  
Closed  
Closed  
-15 dB CSU  
Closed  
-22.5 dB CSU  
Front panel DIP switch #4 (SW5) (Receive Equalizer Gain Limit) should be set to OPEN.  
Front panel DIP switch #5 (SW5) (Lamp Test) should be set to OPEN.  
Front panel DIP switch #6 (SW5) (Customer Disconnect Enable) should be set to OPEN.  
Front panel DIP switch #7 (SW5) (Local Loop Back) should be set to OPEN.  
Front panel DIP switch #8 (SW5) (Remote Loop Back) should be set to OPEN.  
\\s_eng\gtcproddocs\standard ioms - current release\42004 instr. manuals\42004-693l2c.doc  
04/06  
 
Pub. 42004-693L2C  
Page: 12 of 15  
Model 69320-101 Voice Network Adapter  
Operation  
After installation, the Model 69320-101 Voice Network Adapter (VNA) should start automatically. The  
VNA requires no direct user intervention during normal operations.  
Installation and Maintenance  
Direct questions about installation of this product to the GAI-Tronics Field Service Department at 800-492-  
1212 inside the USA or 610-777-1374 outside the USA.  
Installation Guidelines  
WARNING  
Disconnect power to the card rack before performing any maintenance.  
Installation Instructions  
1. Remove the VNA from its protective carton.  
2. Verify that power is disconnected to the card rack prior to installation.  
3. Verify that the switch and jumper settings described in the Switch and Jumper Settings section on page  
4 are set in accordance with the instructions in your system manual.  
4. Align the VNA into the upper and lower tracks for the card rack slot.  
5. Slide the VNA toward the rear of the card rack until it comes in contact with the connector on the  
backplane.  
6. Firmly press on the front bezel until the VNA is seated in the backplane connector, and tighten the two  
screws located on the front bezel to secure it to the card rack.  
Removing the VNA Card from the Card Rack  
1. Remove power from the card rack.  
2. Remove the two screws on the front bezel that secures the VNA to the card rack.  
3. Gently disengage the VNA from the connector on the backplane and slide the VNA out of the card  
rack.  
\\s_eng\gtcproddocs\standard ioms - current release\42004 instr. manuals\42004-693l2c.doc  
04/06  
 
Pub. 42004-693L2C  
Page: 13 of 15  
Model 69320-101 Voice Network Adapter  
Frequently Asked Questions  
Q: Is the 69320-101 VNA compatible with the public switched telephone network?  
A: No.  
Q: When does the 69320-101 VNA generate at T1 Yellow Alarm?  
A: Never.  
Q: When does the 69320-101 VNA generate a T1 Blue Alarm?  
A: Never.  
Q: What is the T1 Red Alarm?  
A: The T1 Red Alarm is the Loss of Signal (LOS) or Receive Carrier Loss (RCL) condition.  
Q: Why do the LEDs have two labels?  
A: One label is the newer vernacular; the other is the older vernacular.  
Q: Why does the front panel “Lamp Test” switch not function while the VNA detects the MCU is running  
(the MCU FLT LED is off)?  
A: That behavior is by design. That design choice helps prevent the diagnostic function of the front panel  
LEDs from being defeated while the system is in use.  
Q: What feature does setting all front panel DIP switches to closed enable?  
A: Doing so enables all four relays on the VNA, lights all LEDs on the VNA, and routes a 2.0000 kHz tone  
(assuming a different signal has not been loaded after power up) to all backplane audio lines and backplane  
ST-Bus data lines. This feature is used to approximate the maximum power consumption and  
electromagnetic emissions of the VNA. This feature interferes with normal system operations, and is  
disabled while the VNA detects the MCU is running.  
Q: Is the 69320-101 VNA capable of generating E1 timing instead of T1 timing.  
A: No.  
\\s_eng\gtcproddocs\standard ioms - current release\42004 instr. manuals\42004-693l2c.doc  
04/06  
 
Pub. 42004-693L2C  
Page: 14 of 15  
Model 69320-101 Voice Network Adapter  
Specifications  
Electrical  
Board  
Power............................................................................................... 950 mA maximum @ +5 V dc ± 5%  
125 mA maximum @ +12 V dc ± 10%  
125 mA maximum @ -12 V dc ± 10%  
T1 Parameters  
NOTE: the 69320-101 VNA is not compatible with the public switched telephone network.  
Encoding..................................................................................... (Bipolar with 8 Zero Substitution) B8ZS  
Framing..........................................................................................................(Extended Superframe) ESF  
T1 Cabling  
Type..................................................................................................... Twisted pair (i.e., CAT.5 ethernet)  
Cable characteristic impedance..................................................................................... 100 ohms nominal  
Maximum cable length .............................................................................................................. 6,000 feet  
Digital Audio - Party Line or Narrow Bandwidth Paging  
Encoding.................................................................................µ-Law per CCITT Recommendation G.711  
Sampling rate .................................................................................................................. 8 kHz ± 32 ppm  
Digital Audio - Wide Bandwidth Paging  
Encoding.................................................... ADPCM 32 kbps, µ-Law per CCITT Recommendation G.726  
Sampling rate encoding ................................................................. 8 kHz up sampled to 16 kHz ± 32 ppm  
Sampling rate decoding ............................................................ 16 kHz down sampled to 8 kHz ± 32 ppm  
Card Rack Page Audio from one VNA to another VNA in a different Card Rack – Narrow Bandwidth  
Frequency response........................................................................................ 250 Hz to 3.5 kHz ± 0.5 dB  
Distortion..........................................................THD <2.0% @ 1,020 Hz sine wave, -10 dB ref. 1.5 Vrms  
Card Rack Page Audio from one VNA to another VNA in a different Card Rack – Wide Bandwidth  
Frequency response........................................................................................ 250 Hz to 3.5 kHz ± 0.5 dB  
Distortion..........................................................THD <2.0% @ 1,020 Hz sine wave, -10 dB ref. 1.5 Vrms  
Card Rack Party Audio from one VNA to another VNA in a different Card Rack  
Frequency response........................................................................................ 250 Hz to 3.5 kHz ± 0.5 dB  
Distortion..........................................................THD <2.0% @ 1,020 Hz sine wave, -10 dB ref. 1.5 Vrms  
\\s_eng\gtcproddocs\standard ioms - current release\42004 instr. manuals\42004-693l2c.doc  
04/06  
 
Pub. 42004-693L2C  
Page: 15 of 15  
Model 69320-101 Voice Network Adapter  
Environmental  
Temperature range (operating/storage).............................................. +32 °F to +122 °F (0 °C to +50 °C)  
Relative humidity:........................................................................................ 10% - 85% non-condensing  
Mechanical  
Unit dimensions ............................................ 10.3 H × 0.780 W × 9.07 D inches (262 × 19.9 × 231 mm)  
Unit weight ................................................................................................... 0.86 lbs. nominal (0.39 kg)  
Approval  
CE Mark ....................................................... Complies with Low Voltage Directive 73/23/EEC, and the  
EMC Directive 89/336/EEC amended by the Directive 93/68/EEC.  
Replacement Parts  
The 69320-101 VNA has no field replaceable components.  
\\s_eng\gtcproddocs\standard ioms - current release\42004 instr. manuals\42004-693l2c.doc  
04/06  
 
Warranty  
Equipment. GAI-Tronics warrants for a period of one (1) year from the date of shipment, that any  
GAI-Tronics equipment supplied hereunder shall be free of defects in material and workmanship, shall  
comply with the then-current product specifications and product literature, and if applicable, shall be fit  
for the purpose specified in the agreed-upon quotation or proposal document. If (a) Seller’s goods prove  
to be defective in workmanship and/or material under normal and proper usage, or unfit for the purpose  
specified and agreed upon, and (b) Buyer’s claim is made within the warranty period set forth above,  
Buyer may return such goods to GAI-Tronics’ nearest depot repair facility, freight prepaid, at which time  
they will be repaired or replaced, at Seller’s option, without charge to Buyer. Repair or replacement shall  
be Buyer’s sole and exclusive remedy. The warranty period on any repaired or replacement equipment  
shall be the greater of the ninety (90) day repair warranty or one (1) year from the date the original  
equipment was shipped. In no event shall GAI-Tronics warranty obligations with respect to equipment  
exceed 100% of the total cost of the equipment supplied hereunder. Buyer may also be entitled to the  
manufacturer’s warranty on any third-party goods supplied by GAI-Tronics hereunder. The applicability  
of any such third-party warranty will be determined by GAI-Tronics.  
Services. Any services GAI-Tronics provides hereunder, whether directly or through subcontractors,  
shall be performed in accordance with the standard of care with which such services are normally  
provided in the industry. If the services fail to meet the applicable industry standard, GAI-Tronics will  
re-perform such services at no cost to buyer to correct said deficiency to Company's satisfaction provided  
any and all issues are identified prior to the demobilization of the Contractor’s personnel from the work  
site. Re-performance of services shall be Buyer’s sole and exclusive remedy, and in no event shall GAI-  
Tronics warranty obligations with respect to services exceed 100% of the total cost of the services  
provided hereunder.  
Warranty Periods. Every claim by Buyer alleging a defect in the goods and/or services provided  
hereunder shall be deemed waived unless such claim is made in writing within the applicable warranty  
periods as set forth above. Provided, however, that if the defect complained of is latent and not  
discoverable within the above warranty periods, every claim arising on account of such latent defect shall  
be deemed waived unless it is made in writing within a reasonable time after such latent defect is or  
should have been discovered by Buyer.  
Limitations / Exclusions. The warranties herein shall not apply to, and GAI-Tronics shall not be  
responsible for, any damage to the goods or failure of the services supplied hereunder, to the extent  
caused by Buyer’s neglect, failure to follow operational and maintenance procedures provided with the  
equipment, or the use of technicians not specifically authorized by GAI-Tronics to maintain or service the  
equipment. THE WARRANTIES AND REMEDIES CONTAINED HEREIN ARE IN LIEU OF AND  
EXCLUDE ALL OTHER WARRANTIES AND REMEDIES, WHETHER EXPRESS OR IMPLIED BY  
OPERATION OF LAW OR OTHERWISE, INCLUDING ANY WARRANTIES OF  
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.  
Return Policy  
If the equipment requires service, contact your Regional Service Center for a return authorization number  
(RA#). Equipment should be shipped prepaid to GAI-Tronics with a return authorization number and a  
purchase order number. If the equipment is under warranty, repairs or a replacement will be made in  
accordance with the warranty policy set forth above. Please include a written explanation of all defects to  
assist our technicians in their troubleshooting efforts.  
Call 800-492-1212 (inside the USA) or 610-777-1374 (outside the USA) for help identifying the  
Regional Service Center closest to you.  
(Rev. 10/06)  
 

Graco Microscope Magnifier 245081 User Manual
Greenheck Fan Ventilation Hood EM 30 Series User Manual
Hamilton Beach Water Dispenser D50042 User Manual
Harbor Freight Tools Drill 44846 User Manual
Hasbro Motorized Toy Car 33392 User Manual
Honeywell Furnace 62 2030 01 User Manual
Hotpoint Dishwasher HDA100 User Manual
HP Hewlett Packard Scanner 3300C User Manual
HP Hewlett Packard Scanner L2738A User Manual
Husqvarna Blower 115 24 05 95 User Manual